Hanging Faux Stained Glass Panels (Made with Laminating Pouches, Alcohol Ink, and Vinyl Decals)


Previously on Sarah Jane's Craft Blog:


I made some faux stained glass panels by alcohol inking the inside of laminator pouches and then applying stained glass patterns that I cut out of vinyl on my Silhouette Cameo.


It's been a busy couple of weeks here, but I finally managed to get my plastic "stained glass" panels hung up. I went into my sewing kit and grabbed the largest metal needle I could find and then used a lighter to heat the tip. I held it in the flames for a ten count to warm the needle.


Then I stuck the warmed tip of the needle into the laminating film to create a small hole. Be careful with the needles. I grabbed it in the center once and almost burned my finger. Make sure to only heat the very tip and to only hold it on the eye end.


Then I used fishing line to string up the panels. I tied a square knot in the fishing line and then poked it through the hole in the plastic panel to hang. I even connected my small squares into a hanging trio. 


This method for hanging the panels worked perfectly and it makes me want to try out more designs where I can connect multiple panels like my trio.

Comments

Post a Comment

Popular posts from this blog

Plastic Wrap Alcohol Ink on Small Ceramic Bowl

Image
A while back I picked up some small white bowls from Big Lots ( these look similar ) with a nice satin finish. I already inked one bowl using the flame method , but I still have a few bowls left, so I decided to give one the plastic wrap treatment. I got out my craft mat and some alcohol inks . Then I cleaned my bowl with rubbing alcohol on a paper towel and removed the sale sticker from the bottom. I tore a piece of plastic wrap off the roll that was large enough to cover my bowl, and I set it down on my craft mat, being sure not to smooth it out. Then I dripped ink on the plastic wrap until I liked the combination of colors and the plastic was mostly full of color. Then I placed my bowl in the center of the plastic wrap and carefully applied the plastic wrap to the sides without smoothing it out too much (so it keeps the wrinkled pattern). Then I flipped it over to dry. I ended up using 7 colors on the bowl. I wanted something bright and fun so I we...
Read more

Alcohol Ink Laminator Pouch Sun Catchers

Image
A couple of weeks ago, I tried making sun catchers with laminating pouches and tissue paper. The project worked pretty well, and I wondered if I could use ink on those laminating pouches--they are plastic after all, which usually inks well. So I got out my alcohol inks , a craft mat to protect my table, a can of air , and my laminating pouches . I opened up my laminating pouch, and I chose a rainbow of ink colors. I wanted something bright and fun. I started with some sailboat blue drops that I spread out with the canned air.  I kept dropping ink onto the surface of the laminating pouch and blowing it around to spread it out and dry it. The surface of the laminating pouches is textured to keep items from slipping around too much in the pouch, so the textured surface absorbed the ink a bit, but it still worked pretty well. I did get a bit of ink on the opened side of the pouch and a bit along the edges, but I wasn't too worried about it being perfe...
Read more

Alcohol Ink Washer Necklaces

Image
I received a package of alcohol inks for Christmas and then bought a second set with a 50% off coupon at Michael's.  I've used them now to make coasters and to decorate some candle holders .  I was just getting my sea legs with these inks to begin with.  I applied the ink directly onto the surfaces and played around with rubbing alcohol as a blending solution.  But I thought it was high time that I used an applicator to use them the way they were intended.  Of course, the applicator is just a stamp with some velcro on it and it costs 6+ dollars....not to mention buying the pre-cut pieces of felt. So I figured I'd make my own.  I was very much in a use what you've got mentality, so I grabbed a scrap piece of wood and a couple of strips of velcro (hook and loop tape).  I used the hook side and lined two pieces up next to each other.  Luckily they were just the right width. I had the sew-on kind of velcro, so I spread some tacky glue ...
Read more